Mustang II 2 1974-78 Tubular Lower And Upper Control Arm Set pro v8 hot

Mustang II 2 1974-78 Tubular Lower And Upper Control Arm Set pro v8 hot
Mustang II 2 1974-78 Tubular Lower And Upper Control Arm Set pro v8 hot
Mustang II 2 1974-78 Tubular Lower And Upper Control Arm Set pro v8 hot
Mustang II 2 1974-78 Tubular Lower And Upper Control Arm Set pro v8 hot
Mustang II 2 1974-78 Tubular Lower And Upper Control Arm Set pro v8 hot
Mustang II 2 1974-78 Tubular Lower And Upper Control Arm Set pro v8 hot
Mustang II 2 1974-78 Tubular Lower And Upper Control Arm Set pro v8 hot
Mustang II 2 1974-78 Tubular Lower And Upper Control Arm Set pro v8 hot
Mustang II 2 1974-78 Tubular Lower And Upper Control Arm Set pro v8 hot
Mustang II 2 1974-78 Tubular Lower And Upper Control Arm Set pro v8 hot
Mustang II 2 1974-78 Tubular Lower And Upper Control Arm Set pro v8 hot
Mustang II 2 1974-78 Tubular Lower And Upper Control Arm Set pro v8 hot

Mustang II 2 1974-78 Tubular Lower And Upper Control Arm Set pro v8 hot
Johnny Law Motors brings you the vey best in aftermarket and OEM car and truck parts and accessories. We offer a HUGE selection of the top brand products at the lowest prices. The only thing that beats our low prices is our great customer service. We are here to help you build your ride with the best parts and service in the industry. Mustang II 2 1974-78 Tubular Lower And Upper Control Arm Set pro v8 hot. Reference part number: JLM 9BF25. Mustang II Tubular Control Arm Set by JLM includes 2 upper control arms and 2 lower control arms. Everything you need in one kit! These control arms are a fully assembled, ready-to-install, direct replacement for stock upper and lower control arms on any JLM Mustang II IFS application and will fit most stock or aftermarket crossmembers with gussets installed. The lower arms are a direct replacement for stock Mustang II LCAs with standard springs. The JLM upper control arm assembly features 12 point TIG welded construction for maximum strength and durability, corrosion/rust resistant painted surface (except powder coated cross shaft), full. 120 wall aircraft quality tubular design which is lighter weight yet much stronger than OE stock design and provides for more clearance for body sheet metal. Complete assembly includes cross shaft with polyurethane no-squeak bushings & steel sleeves, knurled surface mount area on cross shaft, screw-in ball joint with urethane dust boot and grease fitting, castle nut w/ cotter pin, castle nut spacer, 2 ea. Nyloc nuts and plain washers. These upper control arms are a stock width design (non-narrowed) and ready to drop in immediately out of the box. For all of your suspension needs, JLM delivers the winning edge for maximum performance when it really counts! Cross Shaft has knurled surface area on both sides of mounting points which provides bite into mounting surface area so as to prevent slippage and hold alignment settings. Surface area on cross shaft is unfinished and repainting/refinishing shaft is not recommended because any type of body filler or thick paint will prevent knurls from biting properly which can cause slippage and loss of alignment adjustment. The JLM lower control arm assembly features precision fabricated TIG welded construction and 1 inch O. Aircraft quality tubular steel design with full. 120 wall for maximum strength and durability. This makes for a lighter weight yet much stronger LCA than the original stock arm that will endure a far higher stress load than the OEM design. Complete left and right assembly includes 2 ea. 5/8-11 x 12 hex bolts (cross shaft), nylon locking nuts and large 5/8 washers, built-in polyurethane no-squeak bushings w/ steel sleeves, screw-in ball joint with urethane dust boot & grease fitting, 7/16-14 x 7 hex bolt (Allen head), castle nut w/ cotter pin, and castle nut/ball joint spacers 2 ea. This lower control arm assembly is stock design and ready to drop in immediately out of the box. For all of your suspension needs, JLM deliver the winning edge for maximum performance when it really counts! Includes :: 2 Tubular Upper Control Arms & 2 Tubular Lower Control Arms Application :: Mustang II Type :: Tubular Tube Finish :: Plain Painted Surface Cross Shaft Finish :: Powder Coated Screw In Ball Joint :: Yes Feature :: All Steel Construction TIG Welded :: Yes Grease Fitting Included :: Yes Urethane Dust Boot :: Yes Fully Assembled :: Yes Adjustable :: No Tube O. (25 mm) Feature :: Full. 120 Wall Tubing Upper Control Arm Center to Center Length :: 8 (20.32 cm) Upper Control Arm Feature :: (Ball Joint Shaft Center to Cross Shaft Eye Center) Upper Control Arm Overall Width :: 10.5 (26.67 cm) Upper Control Arm Overall Length :: 9.5 (24.13 cm) Upper Control Arm Cross Shaft O. 78 (19.8 mm) Lower Control Arm Overall Width :: 10.5 (26.7 cm) Lower Control Arm Overall Length :: 14.75 (37.46 cm) Lower Control Arm Cross Shaft O. : 5/8 (16 mm) Hardware Included :: Yes. If you are purchasing multiple items, please pay for all items at the same time. All items must be in original condition including the packaging. Some items may have defects, but will still work for the application, unless otherwise stated as inoperable. An example is shift knobs which were molded slightly oblong, or dont seat squarely at a 90 degree angle to the shift rod. We made every effort to document every last imperfection, but we may have missed something. That said, I personally sealed the last hundred, and I recall about 3 missing it. We have since found more, so just let us know! The item “Mustang II 2 1974-78 Tubular Lower And Upper Control Arm Set pro v8 hot” is in sale since Saturday, February 2, 2019. This item is in the category “eBay Motors\Parts & Accessories\Car & Truck Parts\Suspension & Steering\Control Arms & Parts”. The seller is “johnnylawmotorsonline” and is located in Portland, Oregon. This item can be shipped worldwide.
  • MPN: JLM9BF25
  • Brand: Johnny Law Motors

Mustang II 2 1974-78 Tubular Lower And Upper Control Arm Set pro v8 hot

Comments are closed.